Gauntlet Tutorial from Patterning to Assembly!

We asked Piratica (Captain Pira on Instagram) to create a tutorial for us using Black Worbla and she shared this great writeup on making a gauntlet, using Flemmeth from Dragon Age as an example!

You will need:
Cheap gloves with minimal stretch (these will be ruined, don’t use the gloves for your costume)
A marker
Paper
Sharp Scissors (not your fabric scissors!)
Worbla (approx 11×17 or 6×20, twice your paper pattern)
Pencil
Heat Gun
Heat Protection Gloves
Glue of choice (hot glue, E6000 or crazy glue)


1. Gather your references. Front, back, sides. Trying to understand how it works before you start always makes things go smoother.

2. Put on your glove. If you’re only making one (like McCree or Asami’s glove) put on the wrong glove inside out. You’ll be ruining this glove so don’t use the one you’ll want in your finished piece.

3. Using your marker, draw circles around your knuckles and lines where your fingers bend onto your glove. Whatever design you’re making, you’ll want to be able to bend your fingers. Remember your thumbs.

4. Start to draw your design. This glove has pointed fingers and knuckles, so I continued segments into points over the knuckles. Also draw on any panels for the back of your hand, or indications where rivets or crests might go. Drawing a line around where your wrist bends can also help you build a more wearable glove.

5. When your glove has all the details you want in your gauntlet, take it off and cut out your finger segments. I recommend cutting across around the knuckles, and then snipping them open on the palm-side to create a flat piece. Trace this piece out onto paper.

If your design has overlap, like the knuckle spikes here, it’s usually easiest to cut it at the knuckle, then when you draw your piece on paper, to continue the circle you marked your knuckles with. This allows me to make sure the knuckle is covered at the hidden end, and shows me how big to draw my spikes on the pointed end.

For finger tips, if you want finger shaped ones (like Iron Man) use the glove tips, but cut more darts to get your flat pattern. Spiky fingers are done by adding to the flattened design. I added an extra cm at the tip, and tapered to it. If you want your fingertips to curve in like claws, you’ll want a Star Trek logo shape (as I switched to after this step), but if you want them to curve straight on the top, you’ll want to make a shield shape (as above).

6. Continue to cut pieces out from your glove and trace them onto paper until you have all your pieces. Label as you go! Finger pieces tend to look similar but fit very differently. A naming system like Pinky 1, Pinky 2, Pinky 3, Ring 1, etc can save you a lot of headache later.

7. TEST YOUR PATTERN. Cut out all your paper finger joints and try them on, over a new, whole glove. If your original glove stretched to fit your hand, you’ll probably need a few extra mm at each end to compensate, plus the added bulk of the glove itself.

The easiest way to test and expand a pattern is to put masking tape on one end, put the piece in place on your gloved hand, then connect the other end with the tape, where it closes comfortably. Then slide the segment off your finger, and snip apart the masking tape to have your new fitted size.

8. When you’re happy with the fit of your pattern, trace your paper pattern onto the matte side of your Worbla with pencil. Label these too! Finger joints are small, so instead of covering a layer of foam, use two layers of Worbla. Try to Tetris your pieces to save material, and have enough space to either fold your Worbla over or cut out another piece the same size.

9. Heat your sheet! Before cutting out every piece, cut out the whole area you’ve drawn pieces on, and a second piece the same size (if your shape isn’t a rectangle, make sure to cut the 2nd shape mirrored). Put on you heat gloves and use your heat gun to warm both pieces until they are approaching the activation temperature. Press them together with the shiny sides in. Place this on a flat surface and continue to heat it until it reaches the activation point. Press gently and make sure your pieces are joined evenly.


10. Allow to cool enough your pieces won’t warp, then cut out all your pattern pieces.

Keep your scraps for making rivets, details or other projects.


11. Now the fun part. Grab a finger joint and heat it up. Wrap it around a heat glove covered finger until it is cool enough to touch.

Then put on your costume glove, and wrap the piece around the appropriate joint, connecting the sides around your finger and smooshing them flat and securely. In this design I wanted a ridge leading to the points, you can add that by pinching along a line. Also curving the opposite end around your knuckle will help it tuck underneath the next segment.


Rows 2 and 3 should be made this way.

12. Fingertips are a bit different, but mostly consist of pinching the heated Worbla from the ends to the tip, then bending the amount of curve you want. Try your pieces on together as you go, and don’t be afraid to reheat parts to adjust the fit.

13. Hand panels are even easier. Just heat them then shape them on your hand where you need them. Do any pieces that connect in order, so they’ll still be warm when you join them. This design has an open palm, so all the hand pieces can be connected without hindering movement.

14. If you have any details, like the knuckle mounds here, add them now. For these knuckles, little balls of scrap Worbla were rolled and stuffed underneath the diamond shapes to give them dimension, then the diamonds were pinched to create ridges.

15. Try on all your pieces at once! You should be able to wear most of these like rings, and fit the tips on far enough to test the motion. Spread your fingers, make a fist. Make sure you’ll be able to do whatever cool pose you’ll want to make at con. If you’re satisfied with the fit, it’s time to prime. When you’re done painting and want to finish your gauntlet, put on your glove and put a drop of glue on your glove’s finger segment, slide on your Worbla, and press it down. Repeat for each piece.

Dragon Age Morrigan Necklace

Laura Sánchez aka Nebulaluben created this beautifully detailed necklace for her Ballgown Morrigan from Dragon Age Inquisition. You can find her tutorial below!

Picture by Jesús Clares. Commisioned for EA Spain.
Picture by Jesús Clares. Commisioned for EA Spain.

Hello everybody!! Today it’s time to write about my Morrigan necklace so let’s go!

To make the pattern, I wrapped myself in plastic and masking tape to get a basic shape. I drew its shape with its details and I cut it out to obtain the pieces.
As always, I just made one half to make it symmetrical later.

2014-10-12 13.41.47
2014-10-12 13.45.22
2014-10-12 13.58.07
2014-10-12 14.01.34
2014-10-12 14.05.35

I made most of the necklace using Worbla but the pendant, that was the same from DAO and I already had its mold. I made the necklace base with a Worbla sheet and I shaped it with the heat gun.

2014-10-12 14.06.43
2014-10-12 14.13.05
2014-10-12 14.15.41

Then I cut the strips and the leaf shaped ornaments and I stuck them using the heat gun again. The smaller blue ornaments were made using thin craft foam.
2014-10-23 13.39.32

I glued the polyurethane resin pendant with epoxi glue.

2014-10-23 20.27.46

I primed the collar with a couple wood glue layers and priming spray. It needs a lot of work to smooth it out.
After priming, I had to sand it conscientiously till it looked smooth enough.

Before sanding.
Before sanding.
After sanding.
After sanding.

Once the surface was ready, I painted it with a layer of brown acrylic and, to finish it, I used my favourite golden paste.
2014-10-28 10.22.16
2014-10-28 11.05.34
2014-10-28 11.07.29

And done!
2014-10-29 10.37.16
10676358_10154792814790403_4590652536107110459_n

I don’t quite like the final shape of this collar. I mean, it’s not bad, but I’d like it to be a litle wider. I was in a rush while making this costume, so I didn’t have time to remake it. Anyway, I hope you find this tutorial useful.
As always, you can follow me on my social media and feel free to ask me anything in the comments below.
Thanks for reading!

Thanks again to Laura Sánchez for sharing this tutorial with us! You can find her on Instagram, Twitter, and DeviantArt.

Inquisition Buttons (Recycling Worbla)

Karin Olava Effects shared this great idea for turning your Worbla scraps into buttons. You can use this idea to make any sort of design, or even make small creatures or pendants (perfect for gifts!)

Got worbla scraps?

I have a lot of worbla scraps and leftovers that I don’t really know what to do with. Of course you can shape it into spikes and skull details for you armour, and some ever make new sheets from it. But I’m going to show you how you can make geeky little gifts for your friends! It’s quick, easy and fun!

button1
Fist you are going to need some buttons. I use leftover ones from work. Then gather your worbla scraps, heat and start shaping it into the patterns you want. Because of all the Dragon Age Inquisition updates from Bioware lately, I’ve opted for some Inquisition logo styles. If the worbla won’t stick to the button once it’s cooled down, just glue it down with some contact glue.

button2
When you have your base done, it’s just to prime with woodglue. Some people prefer to use gesso, but for something quick like this I just add three layer of woodglue. After that it all dry it’s just to pick you colors and paint! I use normal acrylic paints. And for a more beaten up look I like to weather my pieces. Here I simple paint on some black in the nooks and crannies and wipe it off with a paper towel. Leaving some paint for a dirt like effects. You can of course go over with more brown tones for a rusty look.

button3
You could just clearcoat them now and be happy, but I’m going about this is typical Dragon Age style. Blood, blood and more blood! >D I like to use Skin Illustrator alcoholic paints in blood tones for this, but normal acrylic paints should do the trick.

Then just a coat of clear lacquer and you done! Neat little geek accessories for you and your friends! And an easy way to get allies for the Inquisition ;)
button4

Thanks to Karin Olava Effects for sharing this with us!